No hiss, noise or distortion either, which was surprising for something supposedly manufactured by Anytone. RX audio is absolutely great, thanks to the generous size of the speaker and cabinet. I was lucky band conditions were reasonably good – South America and India proved to be no problem at all, and the signal reports I got were excellent. I connected the radio to a 5/8λ vertical and made some QSO’s in SSB and FM. I left CB for what it was, and shifted my attention towards the 10 meter band. In CB mode I understood the usefulness of the +10KHz button – it allows you to work on frequencies which are normally skipped in the CB channel system. All settings you made in the menu system are reset to default though, which is a pain. Select one and press FUN again, and switch the radio off and on again. Switching between CB and 10 meters is easy and involves holding down two keys (FUN + SRF) while switching on the radio, after which you’re presented with two options: 1Band (10 meters) or 2Band (CB, 240 channels). The (much more expensive) CRE 8900 does have a micro USB connector at the back – maybe a sign of things to come. Not very user-friendly, a bit silly even. This connector is located on the PCB, which means you have to open up the radio in order to program it. What you won’t find is a micro USB connector to program the radio. At the back we find connectors for the antenna, an external speaker and a CW key. There’s no way to dim the LCD, you can only switch it off. The readability of the bright display (blue, a typical Superstar trade) is excellent, but will hurt your eyes in the evening. Keys react promptly, there are no issues with pots nor with rotary encoders. If this is really an Anytone, this CB radio is assembled on a different (better!) production line than their 2/70 dual bander… The PCB is very neatly built, there are no last-minute ‘Quick & Dirty’ design changes to be found. Whatever the brand name, the overall impression is certainly satisfactory. The board of my review sample for example shows V5, but the firmware is V6.
CRE 8900 CB MOD SOFTWARE
Most of the radios have software version numbers attached to the model, which aren’t necessarily identical to the version number of the PCB. I’m pretty sure you will find this radio under other names I didn’t mention here. The PCB of this version is built a bit differently to make it fit into a DIN enclosure. There’s also a CRE variety, the CRE 8900. This radio can be found under a myriad of names. So, how good (or bad) are these radios really? I gave the Superstar SS6900N the same treatment as any other ham radio equipment I reviewed here, and ended up with some surprising results.
The manufacturer claims the output to be 40 Watts on FM and SSB, and about 12 Watts carrier on AM/CW, all adjustable. They pump out a generous amount of power too, thanks to a couple of IRF520 MOSFET finals (which, BTW, are dirt cheap). They are indeed all-mode: FM, AM, SSB and CW. Please check out the sidebar for frequently asked questions.Yet it would be silly to ignore these radios all together. You can use one of two methods to check your SWR: an antenna analyzer or a stand alone SWR meter.īoth are acceptable, but the antenna analyzer is the best method, giving more accurate results. This helps reduce the standing wave ratio ( SWR) to proper levels.Īn SWR of 1:1 is perfect and almost impossible to achieve outside of a lab.ġ.1-1.5:1 is considered perfect under real world conditions.ġ.6-2.0:1 is Average with room for improvement.Ģ.1-2.9:1 means you need to tune your antenna some more.ģ.0:1 and above is dangerous for your radio and could lead to damaging the radios internals. If you just installed your radio, you will want to make sure that your antenna is tuned properly to the location that it is installed in. Make sure that your antenna is fully plugged in and that your radio is receiving power.
We have an IRC channel where you can arrange skeds and nets or have a chat, details are : For everything CB and Public Radio whatever the band may be!